SpecificationsWingspan: 46 in (1170mm)Length: 36 in (915mm)Wing Area: 370 sq in (23.87 sq dm)Weight w/o Battery: 29–31 oz (680–740 g) Weight w/ Ba
10 E-flite Taylorcraft ARF Assembly Manual 8. Position the servo on the mounting plate so the arm is centered in the notch. 9. Use a pencil to
11E-flite Taylorcraft ARF Assembly Manual 12. Use the hardware provided with the servo to secure it to the blocks using a #1 Phillips screwdriver.
12 E-flite Taylorcraft ARF Assembly Manual 15. Tie the string to the servo extension and pull it through the wing to the center section. 16. A
13E-flite Taylorcraft ARF Assembly Manual 18. Attach the 3 3/4-inch (95mm) aileron pushrod to the middle hole of the control horn. 19. Slide t
14 E-flite Taylorcraft ARF Assembly ManualJoining the Wing PanelsRequired PartsWing (R&L) Wing joinerWing dowel (2) Skylight windowWing bolt bra
15E-flite Taylorcraft ARF Assembly Manual 4. Slide the joiner into the other wing panel. It should slide in the panel up to or farther than the line
16 E-flite Taylorcraft ARF Assembly Manual 8. Finally, apply epoxy to the root ribs that will come in contact with each other. Slide the panels toge
17E-flite Taylorcraft ARF Assembly Manual 12. Position the brace on the trailing edge of the wing. Use a felt-tipped pen to trace the outline of the
18 E-flite Taylorcraft ARF Assembly Manual 14. Remove the covering, exposing the underlying wood. 15. Use a paper towel and rubbing alcohol to rem
19E-flite Taylorcraft ARF Assembly ManualTail InstallationRequired PartsFin/rudder Stabilizer/elevatorFuselage Assembled wing#4 washer (2)4-40 x 1-i
2 E-flite Taylorcraft ARF Assembly ManualIntroductionMany a plane has been called a “classic” but few deserve the title more than Clarence Taylor’s le
20 E-flite Taylorcraft ARF Assembly Manual 3. Position the tail assembly onto the fuselage. The tab on the fin will extend slightly, locking into th
21E-flite Taylorcraft ARF Assembly Manual 5. Use a hobby knife to remove the covering from inside the lines on the bottom of the stabilizer. Again,
22 E-flite Taylorcraft ARF Assembly Manual 8. Stand back from the aircraft about 6–8 feet (2–3 meters) and check that the wing and stabilizer are pa
23E-flite Taylorcraft ARF Assembly ManualServo InstallationRequired PartsControl horn (2) Control horn backplate (2)Micro pushrod connector (2) Conn
24 E-flite Taylorcraft ARF Assembly Manual 4. Snap the control horn backplate on the control horn. Hold the horn while pressing the backplate tigh
25E-flite Taylorcraft ARF Assembly Manual 7. Repeat Steps 1 through 6 to install the elevator pushrod and servo.Landing Gear InstallationRequired Pa
26 E-flite Taylorcraft ARF Assembly Manual 2. Attach the landing gear to the fuselage using two 4-40 x 3/8-inch socket head screws and two #4 washer
27E-flite Taylorcraft ARF Assembly Manual 5. Repeat Steps 3 and 4 to install the remaining wheel. 6. Rest your model on a flat surface. Slide th
28 E-flite Taylorcraft ARF Assembly ManualMotor and Cowling InstallationRequired PartsFuselage assembly Motor w/X-mount & hardwareSpeed control
29E-flite Taylorcraft ARF Assembly Manual 3. Plug the motor wires into the speed control. Secure the speed control to the bottom of the motor box us
3E-flite Taylorcraft ARF Assembly ManualUsing the ManualThis manual is divided into sections to help make assembly easier to understand, and to provid
30 E-flite Taylorcraft ARF Assembly Manual 6. Cut and tape a piece of card stock on both sides of the fuselage to indicate the front edge of the fus
31E-flite Taylorcraft ARF Assembly Manual 9. Position the cowling so the hole for the propeller is centered with the propeller adapter, and so the p
32 E-flite Taylorcraft ARF Assembly Manual 13. Secure the cowl to the fuselage using four 2mm x 8mm sheet metal screws. 14. Secure the propeller t
33E-flite Taylorcraft ARF Assembly Manual 3. Remove the battery hatch from the fuselage. 4. Install the battery in the fuselage using the 8-inch (
34 E-flite Taylorcraft ARF Assembly ManualWindow and Strut InstallationRequired PartsFuselage WingWing strut (2) 2mm x 8mm sheet metal screw (6)Side
35E-flite Taylorcraft ARF Assembly Manual 4. Use canopy glue to secure the seats inside the fuselage. Allow the fuselage to rest on its wheels until
36 E-flite Taylorcraft ARF Assembly Manual 6. Secure the struts to the wing using two 2mm x 8mm sheet metal screws.Control ThrowsUse a ruler to adju
37E-flite Taylorcraft ARF Assembly ManualCenter of GravityAn important part of preparing the aircraft for flight is properly balancing the model.Cauti
38 E-flite Taylorcraft ARF Assembly ManualPreflightCheck Your RadioBefore going to the field, be sure that your batteries are fully charged per the in
39E-flite Taylorcraft ARF Assembly Manual2007 Official AMA National Model Aircraft Safety CodeGENERAL1) I will not fly my model aircraft in sanction
4 E-flite Taylorcraft ARF Assembly ManualImportant Information About Motor SelectionWe recommend the E-flite® Park 450 Brushless Outrunner, 890Kv (EFL
10870© 2007 Horizon Hobby, Inc. 4105 Fieldstone Road Champaign, Illinois 61822 (877) 504-0233 horizonhobby.com E-fliteRC.com
5E-flite Taylorcraft ARF Assembly ManualNotes Regarding Servos and ESCWARNING: Use of servos other than those we recommend may overload the BEC of the
6 E-flite Taylorcraft ARF Assembly ManualDamage LimitsHORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR P
7E-flite Taylorcraft ARF Assembly ManualNon-Warranty RepairsShould your repair not be covered by warranty the repair will be completed and payment wil
8 E-flite Taylorcraft ARF Assembly ManualAileron Servo InstallationRequired PartsWing w/ailerons (R&L) Servo arm (medium length)Micro pushrod con
9E-flite Taylorcraft ARF Assembly Manual 5. Turn on the transmitter and center the aileron stick and trim. Check that any programming has been cl
Comments to this Manuals