E-flite Leader 480 User Manual download pdf (Page 4)

4 E-flite Leader 480 ARF Assembly Manual

Hardware/Accessory Sizes

Wheel diameter 2-in (51mm)

Wing bolts 3mm x 10mm socket

head cap screw

Recommended Radio Equipment

You will need a minimum 4-channel transmitter,

receiver and four servos. You can choose to purchase

a complete radio system. If you are using an

existing transmitter, just purchase the other required

equipment separately. We recommend the crystal-

free, interference-free Spektrum

™

DX6 2.4GHz DSM

6-channel system. If using your own transmitter, we

recommend the following radio equipment.

If you own the Spektrum DX6i radio, or you are

using a different DSM2

™

radio, just add the AR6115

6-channel DSMX microlite receiver and four E-flite

DS76 servos.

Complete Radio System

SPM6610 DX6i DSMX 6CH system

Or Purchase Separately

SPMAR6115 AR6115 6CH DSMX

™

Microlite Receiver

EFLRDS76 DS76 Digital Servo (4)

EFLREX3L 3-inch (76mm) Servo Extension

EFLREX6L 6-inch (152mm)

Servo Extension (3)

480 Motor Setup

EFLM1515 Park 480

EFLA1040L 40-Amp Pro Lite SB

Brushless ESC

EFLB21003S30 2100mAh 3S 11.1V 30C Li-Po,

12AWG EC3

APC12060E 12 x 6E Electric Propeller

Optional Accessories

EFLA110 Power Meter

EFLC505 Intelligent 1- to 5-Cell

Balancing Charger

EFLAEC312 Charge Lead with 12-inch

Wire and Jacks, 16AWG

EFLSP175 1

-inch Aluminum Spinner

with 4mm and 5mm Collets

EFLA156 1/9 Civilian Pilot, Blue

with Glasses

Required Tools and Adhesives

Tools & Equipment

Box wrench: 10mm Felt-tipped pen

Flat file Hex wrench: 1.5mm, 2.5mm

Low-tack tape Pin vise

Ruler Scissors

Side cutter Square

T-pins Two-sided tape

String or dental floss

Drill bit: 1/16-inch (1.5mm), 5/64-inch (2mm)

Hobby knife with #11 blade

Phillips screwdriver: #0, #1, #2

Optional Tools & Equipment

Balancing stand (optional)

Adhesives

Medium CA PAAPT02

Thin CA PAAPT08

Threadlock PAAPT42

Before Starting Assembly

Before beginning the assembly of your model, remove

each part from its bag for inspection. Closely inspect

the fuselage, wing panels, rudder and stabilizer for

damage. If you find any damaged or missing parts,

contact the place of purchase.

If you find any wrinkles in the covering, use a heat gun

(HAN100) and covering glove (HAN150) or covering

iron (HAN101) with a sealing iron sock (HAN141) to

remove them. Use caution while working around areas

where the colors overlap to prevent separating the

colors.

During the course of building your model we

suggest you use a soft base for the building surface.

Such things as a foam stand, large piece of

bedding foam or a thick bath towel will work well

and help protect the model from damage during

assembly. This is not shown in the instructions

to provide the greatest detail in the photos.

1 2 3 4 5 6 7 8 9 ... 31 32

Comments to this Manuals

No comments

E-flite Leader 480 User Manual Page 4

Comments to this Manuals

Related products and manuals for Air equipment E-flite Leader 480