E-flite T-34 Mentor 25e ARF User Manual

SpecificationsWingspan: 55.0 in (1575mm)Length: 44.0 in (1110mm)Wing Area: 545 sq in (34.9 sq dm)Weight w/o Battery: 4.40–4.50 lb (1.90–2.00 kg)We

10 E-flite T-34 Mentor 25e ARF Assembly Manual 2. Attach the nylon steering arm to the nose gear wire. Insert the bend in the wire through the middl

11E-flite T-34 Mentor 25e ARF Assembly ManualMotor and Speed Controller InstallationRequired PartsFuselage assembly Motor with hardwareSpeed control

12 E-flite T-34 Mentor 25e ARF Assembly Manual 5. Use hook and loop tape to secure the speed control to the side of the fuselage. 6. Check the ope

13E-flite T-34 Mentor 25e ARF Assembly Manual 4. Slide the propeller on the adapter. It may be necessary to enlarge the hole in the propeller using

14 E-flite T-34 Mentor 25e ARF Assembly Manual B. Slide the propeller on the adapter. It may be necessary to enlarge the hole in the propeller using

15E-flite T-34 Mentor 25e ARF Assembly Manual 3. Tie the string located inside the wing to the end of the servo lead. Pull the servo lead through t

16 E-flite T-34 Mentor 25e ARF Assembly Manual 9. Slide a silicone keeper on the clevis, then thread the clevis on the linkage wire. With the ailer

17E-flite T-34 Mentor 25e ARF Assembly Manual 5. Connect the linkage to the nylon control horn. Adjust the clevis so the flap is aligned with the tra

18 E-flite T-34 Mentor 25e ARF Assembly Manual 3. Place the servo in the opening. Use a pin vise and 1/16-inch (1.5mm) drill bit to drill the four h

19E-flite T-34 Mentor 25e ARF Assembly Manual 9. Use the flap adjustment of your radio system to set the FULL FLAP position. The measurement for ful

2 E-flite T-34 Mentor 25e ARF Assembly ManualProduct RegistrationRegister your product online at: www.e-fliterc.com/register/Contents of Kit/Parts La

20 E-flite T-34 Mentor 25e ARF Assembly Manual 5. Use two 3mm x 12mm self-tapping screws and a nylon strap to secure the panels together. Holes hav

21E-flite T-34 Mentor 25e ARF Assembly ManualFinal AssemblyRequired PartsFuselage assembly Wing assemblyCanopy hatch Nylon wing bolt (2)Required Too

22 E-flite T-34 Mentor 25e ARF Assembly ManualAileron Low RateUp 1/4-inch (6mm)Down 1/4-inch (6mm)Aileron High RateUp 1/2-inch (13mm)Down 1/2-i

23E-flite T-34 Mentor 25e ARF Assembly ManualFlying Your T-34 MentorYour T-34 Mentor 25e ARF has been designed with performance in mind for spirited a

24 E-flite T-34 Mentor 25e ARF Assembly ManualGlossary of TermsAilerons: Each side of this airplane has a hinged control surface (aileron), located o

25E-flite T-34 Mentor 25e ARF Assembly ManualDAMAGE LIMITSHORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS

26 E-flite T-34 Mentor 25e ARF Assembly ManualUnited Kingdom:Electronics and engines requiring inspection or repair should be shipped to the following

27E-flite T-34 Mentor 25e ARF Assembly Manual8. I will not operate model aircraft carrying pyrotechnic devices which explode burn, or propel a proje

Printed 08/0915923© 2009 Horizon Hobby, Inc. 4105 Fieldstone Road Champaign, Illinois 61822 USA (877) 504-0233 horizonhobby.com E-fliteRC.com

3E-flite T-34 Mentor 25e ARF Assembly ManualRecommended Radio EquipmentYou will need a minimum of a 4-channel transmitter, receiver and four servos. Y

4 E-flite T-34 Mentor 25e ARF Assembly ManualHorizontal and Vertical Fin InstallationRequired PartsFuselage assembly Horizontal stabilizerVertical st

5E-flite T-34 Mentor 25e ARF Assembly Manual 5. Use a #1 Phillips screwdriver to remove the rudder control horn. 6. Using a #1 Phillips screwdrive

6 E-flite T-34 Mentor 25e ARF Assembly Manual 11. Use a #1 Phillips screwdriver to tighten the control horn screw. Reposition the nylon control horn

7E-flite T-34 Mentor 25e ARF Assembly Manual 2. Use medium CA to glue the plywood servo plates in position for the rudder and elevator servos. Make

8 E-flite T-34 Mentor 25e ARF Assembly Manual 8. Use a pin vise and 5/64-inch (2mm) drill bit to enlarge the holes in the servo arm that are 1/2-inc

9E-flite T-34 Mentor 25e ARF Assembly Manual 13. Slide a pushrod keeper on the wire from the underside of the servo arm. Swing the connector around