E-flite Carbon-Z Cub PNP User Manual

Browse online or download User Manual for Air equipment E-flite Carbon-Z Cub PNP. E-flite Carbon-Z Cub PNP User Manual

  • Download
  • Add to my manuals
  • Print

Summary of Contents

Page 1 - Carbon-Z

Carbon-Z® CubInstruction ManualBedienungsanleitungManuel d’utilisation Manuale di IstruzioniIMAA Legal

Page 2

EN®Horizontal Tail Installation1. Slide the horizontal tail tube (A) into the hole in the rear of the fuselage.2. Install the 2 piece (left and ri

Page 3 - The E-flite Carbon-Z Cub

ENMotor and Propeller Installation 1. Correctly align and connect the motor wire colors with the ESC wires.2. Install the motor (A) with pre-insta

Page 4 - AS3X System

EN®Wing InstallationBefore each fl ight, ensure all wing connectors and fasteners are secure.AssemblyAssemble both wings using the following steps. (On

Page 5 - Bind Plug Installation

ENInstallation1. Slide the wing tube (A) into the fuselage.2. Install the left and right wing (B and C) over the wing tube and into the wing slot

Page 6 - Battery Installation

EN®Center of Gravity (CG) The CG location is measured from the leading edge of the wing at the root. This CG location has been determined with the rec

Page 7 - Arming the ESC and Receiver

ENControl Surface CenteringAS3X Control Direction Test IMPORTANT: Perform the Control Direction Test before performing control surface centering.Cont

Page 8 - Landing Gear Installation

EN®Transmitter Setup Transmitter Setup ChecklistBefore binding for Computerized Transmitters (DX6i, DX7/DX7se, DX7s, DX8, DX10t, DX18):1. Choose a b

Page 9 - Rudder Installation

ENFlying Tips and RepairsAlways decrease throttle atpropeller strike.Consult local laws and ordinances before choosing a fl ying location. Flying Field

Page 10 - Horizontal Tail Installation

EN®1. Disconnect fl ight battery from ESC (Required for Safety and battery life).2. Power off transmitter.3. Remove fl ight battery from aircraft.4.

Page 11

ENOptional Camera Mount InstallationThe optional camera mount (EFL1045023) is sold separately. IMPORTANT: Consult local laws and ordinances before ins

Page 12 - Wing Installation

EN®To register your product online, visit www.e-fl iterc.comSafety Precautions and WarningsAs the user of this product, you are solely responsible for

Page 13 - Wing Installation continued

EN®AMA National Model Aircraft Safety CodeEffective January 1, 2011A. GENERALA model aircraft is a non-human-carrying aircraft capable of sustained fl

Page 14 - Control Direction Test

ENProblem Possible Cause SolutionOscillationFlying over recommended airspeedReduce air speedDamaged propeller or spinnerReplace propeller or spinnerIm

Page 15 - ElevatorAileronRudder

EN®Problem Possible Cause SolutionAircraft will not re-spond to throttle but responds to other controlsThrottle not at idle and/or throttle trim too h

Page 16 - Dual Rates, Expos and Mixing

ENLimited WarrantyWhat this Warranty CoversHorizon Hobby, Inc. (“Horizon”) warrants to the original purchaser that the product purchased (the “Product

Page 17 - Flying Tips and Repairs

EN®Declaration of Conformity (in accordance with ISO/IEC 17050-1)No. HH2013081601Product(s): EFL Carbon-Z Cub BNF BasicItem Number(s): EFL10450

Page 18 - Post Flight Maintenance

®Part # | NummerNuméro | CodiceDescription Beschreibung Description DescrizioneEFL1045001 Fuselage: Carbon-Z Cub E-fl ite Carbon-Z Cub: Rumpf Carbon-Z

Page 19

®Part # | NummerNuméro | CodiceDescription Beschreibung Description DescrizioneEFLM7450BL50 Brushless Outrunner Motor, 525KvE-fl ite Carbon-Z Splendor:

Page 20 - FAA Information

© 2013 Horizon Hobby, Inc.E-fl ite, AS3X, Blade, Celectra, EC3, DSM, DSM2, DSMX, the DSMX logo, Z-Foam, Carbon-Z, Bind-N-Fly, the BNF logo, Plug-N-Play

Page 21 - Troubleshooting Guide AS3X

ENTable of ContentsSpecifi cations8.15 lb(3.7 kg)55.8 in (1419mm)84.6 in (2150mm)BL50 Brushless Outrunner Motor, 525KvIncluded Included60-Amp Pro Switc

Page 22 - Troubleshooting Guide

EN®AS3X SystemHorizon Hobby has always made RC sport, scale and unique aircraft with the kind of performance experts appreciate. First used in Blade®

Page 23 - Limited Warranty

ENBinding is the process of programming the receiver to recognize the GUID (Globally Unique Identifi er) code of a single specifi c transmitter. You nee

Page 24 - FCC Information

EN®Low Voltage Cutoff (LVC)Battery InstallationBattery Selection• We recommend the E-fl ite 3200mAh 22.2V 6S Li-Po battery (EFLB32006S30). Refer to th

Page 25 - Dichiarazione di conformità

ENArming the ESC and ReceiverArming the ESC also occurs after binding as previously described, but subse-quent connection of a fl ight battery requires

Page 26

EN®Assembly1. Install 2 tundra tires (A) on the main strut (B) using 4 wheel collars (C) as shown. Ensure the set screws (D) are aligned with the fl a

Page 27 - © 2013 Horizon Hobby, Inc

ENRudder InstallationAssembly1. Slide the rudder’s CA hinges (A) in the hinge slots (B) of the vertical tail. 2. Install the screw (C) in the rudd

Comments to this Manuals

No comments